Lỗi máy CNC Okuma

Lỗi máy CNC Okuma Alarm P List

Sau đây là liệt kê danh sách Lỗi máy CNC Okuma Alarm P List

0700 NC start-up error
0701 P100-Menu initialization failure
0702 Power failure upon start-up
0703 Load information file not found
0704 File load error
0705 Default scheduling table error
0706 Backup data file error
0707 DTL link/unlink error
0708 RT thread stack overflow
0709 Hardware exception
0710 System call error
0711 AlarmService library error
0712 AlarmService internal error (exception)
0713 AlarmService error
0714 Blue screen
0715 P100-Menu error
0716 Floating point exception
0717 PLC control error
0718 Real time thread time over
0719 HXCP thread error
0720 AlarmService internal error
0721 DeviceNet error
0723 DeviceNet I/O data link file read
0725 M code data file
0726 Safety speed data error
0727 MCS firmware doesn’t support POS2 unit
0728 FL-net error
0729 Non-responsive software detected.
0731 R Spec. error
0732 Unable to execute lost motion compensation
0735 MCS DD encoder link error
0736 MCS DD encoder error
0737 MCS DD encoder (slave sensor) detected error
0738 MCS DD encoder initialization failure
0739 MCS DD encoder (slave sensor) initialization failure
0741 MCS firmware version error
0742 Relocation detection error
0744 MCS power supply unit overload
0750 The spec.-code or select-soft. was wrong
0752 VDU communication error
0753 VDU detected error
0754 VDU initialization failure
0755 SIO link error
0756 PSC optical scale encoder error
0757 MF-SAFETY Error
0758 Safety I/O Error
0759 Safety Servo Link Error
0782 Magnetic encoder speed detection error
0783 MCS Rotary encoder 5 initialization failure
0784 MCS Rotary encoder 5 error
0785 MCS Rotary encoder 4 initialization failure
0786 MCS Rotary encoder 4 error
0787 MCS Rotary encoder 3 initialization failure
0788 MCS Rotary encoder 3 error
0789 MCS Rotary encoder 2 error
0790 MCS Rotary encoder 1 initialization failure
0791 MCS Rotary encoder 1 error
0792 MCS Linear scale 4 initialization failure
0793 MCS Linear scale 4 error
0794 MCS Linear scale 3 initialization failure
0795 MCS Linear scale 3 error
0796 MCS Linear scale 2 initialization failure
0797 MCS Linear scale 2 error
0798 MCS Linear scale 1 initialization failure
0799 MCS Linear scale 1 error
0800 Spindle D/A control data file read
0801 TCP/IP board detected error
0802 Load information file not found
0803 File load error
0804 MSB file mismatch
0805 MOP-Tool parameter PBU load
0806 MOP-Tool tool data PBU load
0807 ACP panel status receipt error
0808 Speed change ratio failure
0810 NC I/O data file read
0812 MCS initialization error
0813 MCS Communication error
0814 MCS data file corrupt
0815 PLC real-time task loop error
0816 PLC initialization error
0817 MCS error
0818 ADP initialization failure
0820 Machine data file read
0821 Spindle gear ratio
0822 Wheel data file read
0823 AXIS CONSTRUCTION DATA setting error
0824 Unit connection mistake
0825 AXIS CONSTRUCTION name not set
0826 AXIS CONSTRUCTION DATA file read
0827 Control axis not found
0828 Wire feed axis No. error
0833 MCS option program file not sent
0834 MCS servo data error
0835 MCS communication error
0836 Program request illegal
0837 Loader spec. code data error
0838 Loader backup data file read error
0839 Specification conditions failure
0840 SuperHi-NC specification mismatch
0841 FCP4 board detected error
0842 Safety monitor spec. error
0845 Specification code setting failure
0846 Thermal deviation comp. backup data file read
0847 DNC-DT preload task start error
0848 PSCB error
0849 Synchronous axis tandem control initialization failure
0850 MCS Undefined alarm number
0851 MCS Inverter unit fault
0852 Mistake in data from MCS to NC
0853 MCS CON APA deviation
0854 MCS Power supply unit error
0855 MCS Converter link error
0856 MCS DC-bus voltage alarm
0857 MCS Motor overcurrent
0858 MCS Power unit overheat
0859 MCS Power unit overload
0860 MCS Supply voltage flutter
0861 MCS Inverter capacity differs from spec.
0862 MCS Winding change failure
0863 MCS Encoder link error
0864 MCS Encoder detected error
0865 MCS Encoder initialization failure
0866 MCS Encoder with shaft detected error
0867 MCS Encoder with shaft initialization failure
0868 MCS ABSO SCALE error
0869 MCS ABSO SCALE initialization failure
0870 MCS Magnetic encoder alarm
0871 MCS Resolver alarm
0872 MCS Pulse generator count over
0873 MCS Motor overheat
0874 MCS Servo link error
0875 MCS Servo link disconnection
0876 Mistake in data from NC to MCS
0877 MCS Servo data error
0878 MCS Illegal command
0879 MCS CON speed over
0880 MCS Speed command over
0881 MCS DIFF over
0882 MCS APA speed over
0883 MCS Full-closed APA error
0884 MCS Over speed
0885 MCS Speed deviation over
0886 MCS Collision detected
0887 MCS Urgent-stop time over
0888 MCS Belt is broken
0889 MCS Axis change control error
0890 MCS Independent encoder initialization failure
0891 MCS Calculated current position lies outside range
0892 MCS Motor overload
0893 MCS Safety speed monitor E-Link error
0894 MCS ABSO SCALE sub-slider detected error
0895 MCS Tandem control communication error
0896 MCS Full abso scale link error
0897 MCS Full abso scale error
0898 MCS Full abso scale initialization failure
0899 MCS Axis stop signal error
0940 Time sharing task control
0941 Real-time task control
0942 Real-time task loop error
0943 Main processor name incorrect
0944 Slave processor name incorrect
0945 Memory board/battery life
0951 SMP error
0952 Not equipped with processor board
0954 Peripheral processor start
0955 Spec. code: data file
0956 Backup data file read
0957 Graphic backup data file read
0958 Pitch compensation data file read
0965 Configuration file format error
0971 Cache data: Initialization error
0988 Cache data: Operation error
0989 CPU information table data incorrect
0990 TASK generate error
0991 TASK information table data incorrect
0992 PLC backup data file read
0993 TCP/IP board illegal
0994 TCP/IP configuration file
0995 Machine axis data file
0996 PLC axis data file
0997 PLC monitor backup data file read
0998 PLC sequence program load
0999 Synchronous tap data file read

Lỗi máy CNC Okuma Alarm A List

Below are listed Okuma A type alarms for Okuma OSP-P300S/P300L CNC systems.

1071 Memory board battery depleted. Replace quickly!
1089 PLC alarm No. illegal
1091 PLC alarm message file not found
1092 PLC backup data file write
1093 PLC backup data file not found
1094 PLC back up data file read
1097 Safety speed monitor error
1098 MCS not responsive
1100 Parameters not set
1101 Blue screen
1102 P100-Menu error
1103 AlarmService internal error
1104 DeviceNet slave idle mode
1105 DTL error
1106 FL-net initialization error
1107 Major FL-net error
1108 Non-responsive software detected
1109 Error occurred during CAS
1110 PLC control error
1111 Shutting down to avoid damage
1112 Non-functioning device detected
1113 MCS Parameter learning error
1114 MCS Inertia identification error
1120 Overload detected.
1121 PSC Optical scale encoder error
1122 Safety controller error
1123 Safety speed monitor error
1132 VDU communication error
1133 VDU detected error
1134 VDU initialization failure
1135 MCS DD encoder link error
1136 MCS DD encoder error
1137 MCS DD Encoder (slave sensor) error
1138 MCS DD encoder initialization failure
1139 MCS DD encoder (slave sensor) initialization failure
1144 MCS Power supply unit overload
1146 Tailstock torque over
1150 MCS Undefined alarm number
1151 MCS Inverter unit fault
1152 Mistake in data from MCS to NC
1153 MCS CON APA deviation
1154 MCS Power supply unit error
1155 MCS Converter link error
1156 MCS DC-bus voltage alarm
1157 MCS Motor overcurrent
1158 MCS Power unit overheat
1159 MCS Power unit overload
1160 MCS Supply voltage flutter
1161 MCS Inverter capacity differs from spec.
1162 MCS Winding change failure
1163 MCS Encoder link error
1164 MCS Encoder detected error
1165 MCS Encoder initialization failure
1166 MCS Encoder with shaft detected error
1167 MCS Encoder with shaft initialization failure
1168 MCS ABSO SCALE error
1169 MCS ABSO SCALE initialization failure
1170 MCS Magnetic encoder alarm
1171 MCS Resolver alarm
1172 MCS Pulse generator count over
1173 MCS Motor overheat
1174 MCS Servo link error
1175 MCS Servo link disconnection
1176 Mistake in data from NC to MCS
1177 MCS Servo data error
1178 MCS Illegal command
1179 MCS CON speed over
1180 MCS Speed command over
1181 MCS DIFF over
1182 MCS APA speed over
1183 MCS Full-closed APA error
1184 MCS Over speed
1185 MCS Speed deviation over
1186 MCS Collision detected
1187 MCS Urgent-stop time over
1188 MCS Belt is broken
1189 MCS Axis change control error
1190 MCS Independent encoder initialization failure
1191 MCS Calculated current position lies outside range
1192 MCS Motor overload
1194 MCS ABSO SCALE sub-slider error
1195 MCS Tandem control communication error
1196 MCS Full abso scale link error
1197 MCS Full abso scale error
1198 MCS Full abso scale initialization failure
1199 MCS Axis stop signal error
1200 Stroke end over
1202 Plus variable limit over
1203 Minus variable limit over
1213 User reserve code
1215 S.M command asynchronous
1216 Synchronous P code error
1217 Torque limiter
1218 Torque limiter cancel
1219 Torque limit over
1220 Torque skip condition not satisfied
1221 Duplicate M-code
1222 Interrupt return pointer mismatch
1223 Thread feed command error
1225 Contour generation calculation error
1228 Illegal spindle mode
1229 Max. spindle rotation count not specified
1238 Spindle moved to interference distance
1243 Turret rotation conditions
1245 Axis moved to tool interference area
1257 Axis moved to chuck barrier area
1258 Axis moved to tailstock barrier area
1259 Tow-along tailstock connecting
1260 Tow-along tailstock command not possible
1262 W-axis plus variable limit over
1263 W-axis minus variable limit over
1265 Parts catcher interlock
1272 Load exceeds No.2 limit value
1273 Load monitor command already executed
1278 Laser measurement data NG
1279 IND. CMP. data verification failure
1280 HP9825A unable to receive
1281 Abnormal data from HP9825A
1282 Data error from HP9825A
1283 C-axis command not possible
1299 Axis moved to sub-spindle interference distance
1300 W-axis unable to move
1303 Pickoff index position
1306 Sensor touch G00
1307 No contact with sensor
1309 Sensor protect
1316 ATC manual operation mode impossible
1322 Y-axis parameter illegal
1323 Illegal YS-axis position
1328 Adaptive control communication error
1329 Shift amount error
1332 Spindle belt slip
1334 APA error
1336 Moved inside horizontal barrier area
1338 LOAD MONITOR W overload
1339 Spindle different from position when door open
1345 Unable to move to tool change position
1347 STM time over
1348 Cycle time over
1349 Contour generation impossible
1353 Measurement system error
1355 Tow-along steady rest connected
1356 Steady rest torque over
1357 Positioning uncertain
1367 NC tailstock position error
1376 Cutting error
1393 Tow-along steady rest interference position
1412 HOME POSITION movement interlock
1426 Moved inside barrier area
1431 Safety speed over
1432 Safety monitor error detection
1435 Turret interference
1436 Power ON APA deviation
1440 Steady rest-Tailstock interlock
1441 Safety speed clamp
1453 Heavy work data not found
1460 TEMP RISE LIMIT OVER
1463 Spindle moved inside transportation barrier
1465 Spindle low acceleration mode condition
1466 HOB cutting overload
1467 Position scale error XS-axis
1468 Servo amp error XS-axis
1469 APA speed XS-axis
1470 APA range XS-axis
1471 CON speed XS-axis
1472 Stroke end over XS-axis
1473 Actual position initialization error XS-axis
1474 Learning control error XS AXIS
1475 CAM execution data not selected XS-axis
1476 Learning control command XS-axis
1477 Syncronous mode command
1478 Chuck coordinates mismatch
1479 PSCB command error
1480 DIFF over XS-axis
1481 Drift compensation value over
1482 PSCB Real-time task error
1483 PSCB INT task loop error
1484 PSCB EC task loop error
1485 PSCB Time sharing task error
1486 PSCB Exception error
1487 PSCB Memory test error
1488 PSCB Overheat
1489 First time drift compensation value over
1490 Synchronous mode spindle speed command
1491 Heavy tooling data not found
1492 PSCB P.G. underpulse
1493 PSCB P.G. overpulse
1494 PSCB Minus stroke end over
1500 Workpiece rest interlock
1501 Workpiece rest torque over
1504 Alarm-A at other system
1507 Unable to enter C-axis sync. Mode
1509 A turret and B turret interference
1510 Unable to execute Hi-CUT Pro control
1511 SPM contour control not possible
1512 SPM contour control error
1513 Unable to clamp workpiece
1514 Clutch A slip over limit
1515 Mistake in X, Z commands
1516 NC tailstock slide resistance over
1517 Turret or tool not at index cut position
1519 Spindle phase over limit
1520 Synchronous error limit over
1521 NC tailstock error
1522 Linear guide cover interference area
1523 Workpiece weight data file not found
1524 Feed speed over
1525 M-tool spindle speed over in Hob mode
1526 Turret index error position
1527 Unable to execute while mounting LBB
1528 The attachment status mismatch
1529 M axis belt slip
1530 Steady-rests interference position
1531 Tool posture fluctuation reduction error
1532 Turret interference distance intrusion
1682 Magnetic encoder speed detection error
1683 MCS Rotary encoder 5 initialization failure
1684 MCS Rotary encoder 5 error
1685 MCS Rotary encoder 4 initialization failure
1686 MCS Rotary encoder 4 error
1687 MCS Rotary encoder 3 initialization failure
1688 MCS Rotary encoder 3 error
1689 MCS Rotary encoder 2 error
1690 MCS Rotary encoder 1 initialization failure
1691 MCS Rotary encoder 1 error
1692 MCS Linear scale 4 initialization failure
1693 MCS Linear scale 4 error
1694 MCS Linear scale 3 initialization failure
1695 MCS Linear scale 3 error
1696 MCS Linear scale 2 initialization failure
1697 MCS Linear scale 2 error
1698 MCS Linear scale 1 initialization failure
1699 MCS Linear scale 1 error
1700 Emergency stop
1701 EC overload
1702 BDU overload
1703 EC circuit breaker
1704 Transformer overheat
1705 Oil pressure low
1706 Alarm detected from externally connected device
1707 Stroke end over
1708 Canceling stroke end limit
1709 XA-axis overload
1710 XB-axis overload
1711 ZA-axis overload
1712 ZB-axis overload
1713 Spindle rotation interlock
1714 S.M command asynchronous
1715 Spindle revolution over
1716 M03/M04 change command failure
1717 Unable to use M40, M43, M44 commands
1718 Tow-along tailstock command error
1719 Gear command/position mismatch
1720 Gear command error
1721 Gear neutral
1722 M19 command issued when gear neutral
1723 Z-axis moved to spindle interference distance
1724 Spindle synchronization interlock
1725 Impossible command issued during spindle synchronization
1726 C-axis command not possible
1727 C-axis ON/OFF command not possible
1728 C-axis clamp/unclamp command not possible
1729 Unable to confirm C-axis advance
1730 Turret clamp/position check error
1731 Turret index control alarm
1732 Turret rotation interlock
1733 Tool number input error
1734 Pickoff chuck interlock
1735 Sub-spindle chuck pressure insufficient
1736 Pickoff index interlock
1737 Turret unclamp interlock
1738 Turret rotation impossible
1739 Chuck clamp pressure insufficient
1740 Chuck open/close interlock
1741 Chuck unclamp
1742 Chuck interlock cancel interlock
1743 Index chuck interlock
1744 Air chuck pressure error
1745 Chucking miss
1746 Chuck missclamp
1747 No tailstock quill advance answer
1748 Tailstock quill advance over
1749 Tailstock quill command error
1750 Tailstock interference
1751 Tow-along tailstock ON/OFF interlock
1752 Tow-along tailstock clamp/unclamp error
1753 Parts catcher interlock
1754 Coupling device alarm
1755 Robot inside machine
1756 Loader inside machine
1757 Loader interlock
1758 Loader not at escape position
1759 Loader/robot not at escape position
1760 Revolution tool M13/M14 change not possible
1761 Revolution tool gear mismatch
1762 Revolution tool gear interlock
1763 Tool revolution interlock
1764 Tool rotating when T command issued
1765 Rotation tool index interlock
1766 Rotation tool over speed
1767 M-axis clutch connection error
1768 Sub-spindle rotation over
1769 Sub-spindle index interlock
1770 Door interlock
1771 Door open/close limit switch NG
1772 Door open/close condition
1773 Unable to restore axis position when door closed
1774 Sensor head advance/retract interlock
1775 Touch setter limit
1776 Sensor head not at retract position
1777 ATC change arm position error
1778 No dummy tool in ATC turret
1779 Manual tool change operation interlock
1780 ATC system mode interlock
1781 Loader/robot interference
1782 Power sequence error
1783 Turret unclamp time over
1784 Turret clamp time over
1785 NC parameter data transfer error
1786 Coolant error
1787 Door open/close check NG
1788 Safety door open
1789 Steady rest interlock
1790 Bar feeder not ready
1791 Bar feeder advance/retract interlock
1792 Turret rotation interlock
1793 Side cover interlock
1794 Rear cover interlock
1795 Side cover open/close lmt switch NG
1796 Turret index clutch disconnect error
1797 Invalid mode switch
1798 Steady rest missclamp
1799 Sensor protection cover interlock
1800 Locking switch NG
1801 Bar feeder setting position mismatch
1802 Safety guard interlock
1803 Machine enabling button error
1804 Safety speed monitor output error
1805 Teaching panel enabling switch error
1806 ATC Logic data file error
1807 Shutter close not possible
1808 Safety fence locking switch NG
1809 Manual command time over
1810 Safety guard interlock
1811 Loader axis unable to move
1812 Mist lubrication unit error
1813 2nd spindle condition satisfy
1814 W-axis movement interlock
1815 Face driver pressure insufficient
1816 Safety fence open
1817 Setup switch ON
1818 Hand slide interlock
1819 Hand turning interlock
1820 Turnover interlock
1821 Magazine door lock error
1822 Slide step interlock
1823 Vibration cutter faulty
1824 Oil cooler error
1825 Spindle cooling unit error
1826 Oil air lubrication illegal
1827 Setup switch ON
1828 Laser sensor interlock
1829 Sp. oil air lub. air pressure error
1830 SP. oil air lub. oil level error
1831 Sp. oil air lub. oil pressure error
1832 Unloader advance/retract interlock
1833 Tow-along steady rest unclamp interlock
1834 Door interlock
1835 Workpiece receiver interlock
1836 Interference area intrusion
1837 Worktable overload
1838 Workpiece stabilizer interlock
1839 Deburring tool interlock
1840 M code data file mismatch
1841 Swing interlock
1842 Wrist rotation interlock
1843 Workpiece rest interlock
1844 Workpiece pusher interlock
1845 Hand rotation interlock
1846 Chuck grip confirmation unit faulty
1847 Tailstock air miss detection input NG
1848 Chuck grip failure
1849 Workpiece unloading unit interlock
1850 Robot/Loader emergency stop
1851 Air pressure insufficient
1852 NC alarm
1853 Oil pressure insufficient
1854 Error detected from externally connected device
1855 M code time over
1856 Circuit breaker tripped
1857 Intrusion interlock
1858 No hand open/close output
1859 Swing position no output
1860 Axis interlock
1861 Stroke end over
1862 Canceling stroke end limit
1863 Loader interference
1864 Z/C-axis not in rotation possible area
1865 Swing position indefinite
1866 No workpiece clamped on hand A
1867 No workpiece clamped on hand B
1868 Wrist broken
1869 Hand open/ close interlock
1870 Hand clamp confirmation
1871 Coupling device error
1872 Safety fence interlock
1873 Door interlock
1874 Interlock release NG
1875 Safety fence lock NG
1876 Swing interlock
1877 Robot/Loader power sequence error
1878 Machine start impossible
1879 Workpiece puller holder interlock
1880 Loader hand/machine interference
1881 Part turnover device R clamp empty
1882 Part turnover device L clamp empty
1883 Part turnover device R advanced too far
1884 Part turnover device L advanced too far
1885 Loader/part turnover device interference
1886 Wrist turning position indefinite
1887 Workpiece puller interlock
1888 Backup roller interlock
1889 Auto workpiece I/O unit FWD pressure low
1890 Coolant flow insufficient
1891 Unloader interference position
1892 Unloader interlock
1893 Running mode error
1894 Running mode error
1895 Fire alarm
1896 Air source pressure low
1897 Lower turret drive belt torn
1898 OP panel within interference range
1899 Safety fence open
1900 Plus variable limit over
1901 Minus variable limit over
1920 User reserve code
1922 Torque limit over
1924 Barrier intrusion
1927 M code time over
1928 Cycle time over
1938 Machine start impossible
1939 Hand open/close interlock
1940 Loader Z-axis stopper set
1941 Safety guard interlock
1942 Safety speed over
1943 Safety speed monitor error
1944 Safety monitor error detection
1945 Running mode error
1949 Alarm-A at other system
1950 Safety speed monitor error
1951 Safety controller error
8500 Cut off error
8501 ATC shutter not close
8502 Unable to G21
8503 Spindle internal centering unit interlock
8504 Tool change command
8505 Tow-along steady rest clamp/unclamp
8506 Combination chuck interlock
8507 Automatic lubrication system error
8508 Coolant filter
8509 Cutting feed interlock
8510 Oil unit error
8511 B-axis clamp/unclamp interlock
8512 Turret position uncertain
8513 Coolant interlock
8514 Work conveyor interlock
8515 Work ejector interlock
8516 Touch setter unlock time over
8517 Work hand interlock
8518 Bar Feeder illegal
8520 Stopper interlock
8521 Work measurement operation
8522 Locater oil pressure
8523 Locater condition
8524 Oil motor overload
8525 Coolant motor overload
8526 Spindle cooling motor overload
8527 Oil skimmer overload
8528 Magnet separator overload
8529 Tool monitoring unit error detection
8530 Laser sensor input data error
8531 Door open
8532 Polish Material unit interlock
8536 Operation ready OFF condition
8537 Magazine door Interlock
8538 ATC shutter barrier area
8539 Complete stop
8540 X-axis in interference range
8541 Spindle phase synchronization interlock
8542 Synchronizing spindle phase
8543 Measurement Unit error
8545 Illegal robot/loader request
8546 Rolling-head movement error
8547 Drive jig unit interlock
8548 ACC interlock
8549 ACC door interlock
8550 ACC manual operation mode impossible
8551 Semi-dry unit error
8552 Sub-chuck interlock
8553 ACC airblow interlock
8554 Spindle table rotation
8555 B-Axis movement
8556 No mount magazine
8557 Tool Breakage sensor error
8558 L-tool index command
8559 Part turn device advanced too far
8560 Override switch failure
8561 Grinding whl spindle motor overload
8562 Whl spdl coolant pressure drop/loss
8563 Inverter failure
8564 Turret drive belt disconnection
8566 Tool clamp interlock
8567 Spindle cover open/close limit SW NG
8568 Insulation error
8569 Magazine turn interlock
8570 Magazine tool No.
8571 Irregular coolant level
8572 ATC step time over
8573 Spingdle vibration
8574 MCS operation ready off
8575 Grinding whl spindle unit
8576 Grinding whl spindle unit interlock
8577 Axis interlock
8578 Coupling device interlock
8579 Tailstock and turret interference
8580 Canceling interference detection
8581 Loader automatic operation
8582 Illegal workpiece pusher confirmation
8583 ATC change arm overload
8584 Tailstock high/low change interlock
8585 Coiling prevention equip. interlock
8586 Air picker broken
8587 AREA SENSOR interlock
8588 Coolant Flow
8589 Chip conveyor faulty
8590 Tailstock pedestal condition
8591 C-axis synchronous condition
8592 Synchronizing C-axis
8593 Chip crusher error
8594 Sensor overstroke
8595 Linear guide cover interference
8596 Safety plug interlock
8597 Shuttle device hand clamp empty
8598 Ceiling door interlock
8599 Illegal tool clamp unit
8600 Ceiling door open/close limit SW NG
8601 ATC tool change arm inverter failure
8602 Chip pan cover interlock
8603 C-axis clamp/unclamp condition
8604 Long tool change protection
8605 Drive belt disconnection
8606 APC door open/close limit NG
8607 XB cover interference
8608 Illegal touch setter unit
8609 Axis overheat
8610 Invalid spindle winding condition
8611 Winding change error
8612 APC interlock
8613 APC clamp/unclamp time over
8614 APC escape position
8615 ATC shutter not open
8616 Coolant level low
8617 Thru-the-tool coolant filter clogged
8618 M spindle overload
8619 Machine axis travel limit over
8620 PLC system data
8621 M spindle air curtain pressure low
8622 Hydraulic unit oil level low
8623 Mist air lubrication unit
8624 Axis interlock
8625 Tool revolution command
8626 Ceiling door guide interlock
8627 Long boring bar change protection
8628 Spindlehead lib oil level low
8629 Spindlehead lubricant pressure low
8630 Hydraulic pressure drop
8631 Invalid safety-monitor spec.
8632 UNUSABLE interrupt program
8633 AAC Operation mode impossible
8634 ATC shutter open/close condition
8635 Spindle actual position detection error
8636 RSS unit Battery error
8637 RSS unit Communication error
8638 Sub-spindle head clamp condition
8639 Tailstock control mode ON/OFF cond.
8640 Center partition interlock
8643 Unusable PLC spec. code
8644 Fire extinguish unit power OFF
8645 Fire extinguish unit error
8646 Fire ext. unit power OFF or error
8647 Hand open/close switch NG
8648 Tailstock tool mode mismatch
8649 Measurement sensor unit interlock
8680 Area sensor interlock

Lỗi máy CNC Okuma Alarm B List

Sau đây là liệt kê danh sách Lỗi máy CNC Okuma Alarm B List for Okuma OSP-P300S/P300L CNC systems.

2049 PLC axis stroke end over
2050 PLC axis command
2051 PLC axis continuous positioning over
2052 Blue screen
2053 P100-Menu error
2058 Error occurred while CAS work
2059 Non-functioning device detected
2060 Fan motor error on panel computer unit
2090 The remaining time after relocation has passed
2092 MCS Parameter learning error
2114 MCS Inertia identification error
2120 Overload detected.
2132 VDU communication error
2133 VDU detected error
2134 VDU initialization failure
2135 MCS DD encoder link error
2136 MCS DD Encoder error
2137 MCS DD Encoder (slave sensor) error
2138 MCS DD encoder initialization failure
2139 MCS DD encoder (slave sensor) initialization failure
2144 MCS Power supply unit overload
2150 MCS Undefined alarm number
2151 MCS Inverter unit fault
2152 Mistake in data from MCS to NC
2153 MCS CON APA deviation
2154 MCS Power supply unit error
2155 MCS Converter link error
2156 MCS DC-bus voltage alarm
2157 MCS Motor overcurrent
2158 MCS Power unit overheat
2159 MCS Power unit overload
2160 MCS Supply voltage flutter
2161 MCS Inverter capacity differs from spec.
2162 MCS Winding change failure
2163 MCS Encoder link error
2164 MCS Encoder detected error
2165 MCS Encoder initialization failure
2166 MCS Encoder with shaft detected error
2167 MCS Encoder with shaft initialization failure
2168 MCS ABSO SCALE error
2169 MCS ABSO SCALE initialization failure
2170 MCS Magnetic encoder alarm
2171 MCS Resolver alarm
2172 MCS Pulse generator count over
2173 MCS Motor overheat
2174 MCS Servo link error
2175 MCS Servo link disconnection
2176 Mistake in data from NC to MCS
2177 MCS Servo data error
2178 MCS Illegal command
2179 MCS CON speed over
2180 MCS Speed command over
2181 MCS DIFF over
2182 MCS APA speed over
2183 MCS Full-closed APA error
2184 MCS Over speed
2185 MCS Speed deviation over
2186 MCS Collision detected
2187 MCS Urgent-stop time over
2188 MCS Belt is broken
2189 MCS Axis change control error
2190 MCS Independent encoder initialization failure
2191 MCS Calculated current position lies outside range
2192 MCS Motor overload
2194 MCS ABSO SCALE sub-slider error
2195 MCS Tandem control communication error
2196 MCS Full abso scale link error
2197 MCS Full abso scale error
2198 MCS Full abso scale initialization failure
2199 MCS Axis stop signal error
2200 G-code error
2201 M-code error
2202 Common variable error
2203 System variable error
2204 Sequence name error
2205 Numeric data error
2206 Character use error
2207 Program name error
2208 Character string error
2209 Hexadecimal data error
2210 Spindle max revolution error
2212 G132/G133 command error
2213 Program factor over
2214 Subscript left side incorrect
2215 Local variable use over
2216 System variable setting data over
2217 Output variable setting data mistake
2218 UNUSABLE G-code
2219 UNUSABLE M-code
2220 Subscript left side illegal
2221 UNUSABLE output variable No
2222 UNUSABLE input variable No
2223 UNUSABLE turret direct code
2224 UNUSABLE contour generation command
2225 UNUSABLE Y-Z circle command
2226 UNUSABLE thread cutting command
2227 Mnemonic or local variable mistake
2228 VSET sequence left command mistake
2229 EXPRESSION right side
2230 EXPRESSION calculation error
2231 EXPRESSION syntax incorrect
2232 EXPRESSION subscript mistake
2233 EXPRESSION buffer over
2234 EXPRESSION local variable
2235 Equal does not exist
2236 Program end code not found
2237 BRANCH (IF,GOTO) sequence name
2238 BRANCH(IF,GOTO) condition
2239 Mistake in F command
2240 Mistake in F/E command
2241 Mistake in I command
2242 Mistake in J command
2243 Mistake in K command
2244 Mistake in L command
2245 Mistake in P command
2246 Mistake in S command
2247 No S command
2248 Mistake in T command
2249 Mistake in X command
2250 Mistake in X/Z command
2251 Mistake in Z command
2252 Mistake in arc command
2253 Mistake in angle command
2254 Mistake in thread cutting cycle command
2255 Mistake in arc radius command
2256 Mistake in D command
2257 Mistake in gauging cycle command
2258 Mistake in C command
2259 Mistake in SB command
2260 Mistake in QA command
2261 Mistake in X/Y command
2262 Mistake in incremental command
2263 Command required for X-, Y-axes
2264 Mistake in Y command
2265 Distance calculation over limit
2266 Mistake in R command
2267 Mistake in drilling cycle command
2268 Mistake in angle command
2269 Angle chamfering command error
2270 Mistake in CD command
2271 Mistake in CL command
2272 Mistake in TM command
2273 Mistake in W command
2274 Mistake in CB command
2275 Mistake in HP command
2276 Mistake in CC command
2277 Mistake in torque limit command
2278 SUB PROGRAM repetition
2279 SUB PROGRAM stack
2280 SUB PROGRAM program name
2281 SUB PROGRAM data print
2282 SCHEDULE PROGRAM ‘Q’
2283 SCHEDULE PROGRAM mnemonic code
2284 SCHEDULE PROGRAM program end
2285 SCHEDULE PROGRAM main program load
2286 Plus variable limit over
2287 Minus variable limit over
2288 User reserve code
2289 Unable to write backup data file
2290 Program name not selected
2291 Main sequence error
2292 Restart failure
2293 MDI special G-code
2294 Special G-code table
2295 STM time over
2296 UGC No program end code
2297 UGC DELETE syntax
2298 UGC DEF syntax
2299 UGC TIP syntax
2300 UGC TIF syntax
2301 UGC No shape entry
2302 UGC Illegal numerical data
2303 UGC Illegal character
2304 UGC User variable
2305 UGC System variable
2306 UGC Illegal command
2307 UGC Program factor over
2308 UGC Coordinate data
2309 UGC END syntax
2310 UGC Command over
2311 UGC Command format
2312 UGC Additional parameter
2313 UGC Expression
2314 UGC Figure entry area over
2315 UGC Unable to delete
2316 READ/WRITE No spec
2317 READ/WRITE Buffer over
2318 READ/WRITE Device No.
2319 READ/WRITE Data
2320 READ communication error
2321 WRITE communication error
2322 GET/PUT No spec.
2323 GET/PUT Buffer over
2324 GET/PUT Number of digits
2325 GET/PUT Variable designation
2326 GET Numerical data
2327 Calculation function no spec.
2328 Sub-program no spec.
2329 Sub-spindle interference distance
2330 Input/output variable no spec.
2331 Multiple machining no spec.
2332 Sub-spindle no spec.
2334 In-process gauging no spec.
2335 Post-process gauging no spec.
2336 Animation no spec.
2337 Graphic backup data file write failure
2338 Spindle orientation no spec.
2339 Load monitor no spec.
2340 Thread phase matching no spec.
2341 Circular thread cutting no spec.
2342 Circular thread cutting command
2343 Tool retract no spec.
2344 Tool retract interrupt enable com.
2345 Tool retract interrupt disable com.
2346 Tool retract interrupt return com.
2347 ROBOT no spec.
2348 ROBOT program name
2349 LOADER no spec.
2350 LOADER program name
2351 Coupling device program select no spec.
2353 CHAMFERING G01 mode
2354 CHAMFERING L over
2355 CHAMFERING L illegal order
2356 CHAMFERING X, Z illegal order
2357 CHAMFERING Any angle calculation
2358 CHAMFERING Any angle
2359 NOSE-R COMP. No spec.
2360 NOSE-R COMP. NOSE-R > circle-R
2361 NOSE-R COMP. Calculation
2362 NOSE-R COMP. Cancel G00 G01
2363 NOSE-R COMP. No cross point
2364 NOSE-R COMP. Entrance command error
2365 NOSE-R COMP. Thread cutting cycle
2366 TOOL RADIUS COMP. No spec.
2367 TOOL RADIUS COMP. NOSE-R comp. surface change
2368 TOOL RADIUS COMP. C-axis separation
2369 TOOL RADIUS COMP. QA command
2370 TOW-ALONG TAILSTOCK MOVEMENT no spec.
2371 TOW-ALONG TAILSTOCK MOVEMENT condition
2372 LASER MEASUREMENT no spec.
2373 LASER MEASUREMENT condition
2374 LAP No spec.
2375 LAP B illegal order
2376 LAP D illegal order
2377 LAP DA(DB) illegal order
2378 LAP H illegal order
2379 LAP H-U(W) < D (M73)
2380 LAP U(W) illegal order
2381 LAP U(W) > H
2382 LAP XA(ZA), XB(ZB) illegal order
2383 LAP Calculation error
2384 LAP Down step number over
2385 LAP Entry in LAP
2386 LAP Sequence name
2387 Unable to LAP Control
2388 LAP No G-code
2389 LAP NOSE-R comp. cancel
2390 LAP Entry in NOSE-R comp.
2391 LAP Shape designation
2392 MULTI CYCLE B illegal order
2393 MULTI CYCLE D illegal order
2394 MULTI CYCLE F illegal order
2395 MULTI CYCLE H illegal order
2396 MULTI CYCLE H-U(W) < D (M73)
2397 MULTI CYCLE I,K over
2398 MULTI CYCLE I,K illegal order
2399 MULTI CYCLE L illegal order
2400 MULTI CYCLE Entry in LAP
2401 MULTI CYCLE U(W) illegal order
2402 MULTI CYCLE U(W) > H
2403 MULTI CYCLE X,Z illegal order
2404 MULTI CYCLE Angle
2405 MULTI CYCLE Tool offset
2406 MULTI CYCLE Cycle start point
2407 MULTI CYCLE Entry in NOSE-R comp.
2408 MULTI CYCLE Width
2409 TOOL LIFE CONTROL no spec.
2410 Tool life management No spare tool
2411 TOOL LIFE CONTROL tool group
2412 TOOL LIFE CONTROL no T-entry
2413 TOOL LIFE CONTROL tool offset group
2414 TOOL LIFE CONTROL no T-offset
2415 MULTI-MACHINING CYCLE No spec.
2416 MULTI-MACHINING CYCLE C
2417 MULTI-MACHINING CYCLE I,K
2418 MULTI-MACHINING CYCLE Q
2419 MULTI-MACHINING CYCLE F
2420 MULTI-MACHINING CYCLE L
2421 MULTI-MACHINING CYCLE D
2422 MULTI-MACHINING CYCLE X,Z
2423 MULTI-MACHINING CYCLE SA
2424 MULTI-MACHINING CYCLE Feed G94
2425 MULTI-MACHINING CYCLE A
2426 MULTI-MACHINING CYCLE Thread cycle
2427 MULTI-MACHINING CYCLE U,W
2428 MULTI-MACHINING CYCLE SB
2429 MULTI-MACHINING CYCLE Y-axis mode
2430 ATC no spec.
2431 ATC syntax
2432 ATC TC
2434 ATC TL
2435 ATC MT
2436 ATC MG
2438 Unable to M06/M228 command
2440 Y-axis no spec.
2441 2 saddle machine no spec.
2444 Carrier axis variable limit over
2445 3-D coordinate conversion
2452 Chuck barrier area
2453 Tailstock barrier area
2456 W-axis minus variable limit over
2457 X-axis correction stroke end over
2459 Restart axis position is illegal
2460 Change timing G13/G14
2462 Change timing G122/G123
2463 Change timing G140/G141/G142
2464 Spindle/turret G-code
2465 G122/G123 command mismatch
2466 Unable to issue M100 command during Nose-R comp.
2472 Y-axis control mode
2475 W-axis command G-code
2476 Mirror image coordinate selection
2477 Sub-spindle mode
2478 No workpiece coordinate mode command
2479 Contour generation calculation error
2480 G132/G133 command error
2486 NC turret no spec.
2487 Unable to select coordinates
2488 UNUSABLE X-axis command
2489 NC tailstock parameter error
2490 Chuck pressure out of range
2491 Horizon barrier intrusion
2492 Interrupt program: illegal command
2493 Linked external equipment program selection
2494 Chuck pressure command illegal
2495 Inverse time feed command format
2496 CAM data cannot be transmitted.
2497 T code
2498 Learning cannot be executed.
2499 Spindle marker latch data error
2500 MULTI-MACHINING CYCLE HS,HI,HJ,HK
2501 Recovering synchronous error
2502 Block Delete command error
2503 End sequence name error
2504 PREMIUM THREAD Command error
2505 CAM machine no spec.
2506 Tool center point control not possible
2507 CHP command error
2508 Machining mode command format
2509 MULTI-MACHINING CYCLE Return point
2510 Mistake in torque skip cycle command
2511 Remote buffer operation
2512 M-tool spindle overload
2513 Coordinate calculation
2514 MULTI CYCLE C-axis shift
2515 Remote buffer operation time out
2516 Remote buffer operation communication error
2517 W-axis control mode
2518 Synchronized tapping command
2519 Tailstock control command
2520 Mistake in TP command
2521 Mistake in BT command
2522 Mistake in BA command
2523 Thermistor error
2524 Mistake in AT command
2525 Chuck coordinate change condition
2528 Program selection unsuitable
2529 Thermal deviation compensation
2530 Machining process instruction no.
2531 Mirror turning mode
2532 System variable set condition error
2533 Steady rest over interference pos.
2534 LBB turret rotation impossible
2536 Coordinate movement rotation copy
2537 SLANT PROCESS MODE
2538 Incorrect system variable
2539 Mistake in B command
2541 PROGRAM PRINT command
2542 Feed axis retract function command
2543 Turret index error position
2544 TOOL-ID TOOL DATA
2545 MULTI-MACHINING CYCLE LD
2546 MULTI-MACHINING CYCLE LK
2547 No decimal point
2548 X-, Z-axis synchronized feed mode
2549 Tool no. mismatch after ATC sequence restart
2550 Home position no spec.
2551 External home position command
2552 Barrier area
2555 Linear guide cover interference area command
2557 Illegal steady rest command
2558 Turning position selection
2559 Attachment rotation not possible
2561 Illegal system command variable
2562 Tool posture fluctuation reduction
2563 Mistake in TE command
2564 Index disable position
2565 Load monitor system variable
2566 MULTI-MACHINING CYCLE No M-tool cycle command
2567 No helical cutting specifications
2568 Mistake in OF command
2569 Thermal deviation comp. backup failure
2570 W-axis position condition
2571 W-axis position no spec.
2572 Mistake in RC command
2573 Taper cutting cycle
2575 Mistake in ‘TD’,’TDG’,’OS’ commands
2576 Mistake in H command
2577 No axis movement command
2578 NO D COMMAND
2579 NO L COMMAND
2580 Mistake in XS command
2581 CAM data deployment mode
2582 CAM data file write protect
2583 Compensation value overflow
2584 CON speed XS-axis
2585 XS-axis command turret mode
2586 Synchronous mode execution impossible
2587 No A command
2588 Mistake in OF command
2589 Definition conditions
2590 Y-axis command
2591 Mistake in point command
2592 Transport barrier entry command
2593 Mistake in CF command
2594 Mistake in RJ command
2595 Synchronized rotation speed over
2596 Synchronized tap overload
2597 G15 command
2598 No Spec code. “Tool information management spec”
2599 Command not possible while mounting LBB.
2600 LAW-V machine no spec.
2601 Unable to issue T/TE command simultaneously
2602 SCHEDULE PROGRAM main program load
2603 Spindle rotation fluctuation control no spec.
2604 Tow-along steady rest no spec.
2605 Tow-along tailstock no spec.
2606 READ/WRITE file open
2607 Mistake in AP command
2608 Mistake in ON command
2609 A-axis control no spec.
2610 Zero offset select inpossible
2611 Spindle fluctuation control no spec.
2612 Mistake in TR command
2613 Mistake in MTM command
2614 Mistake in MTS command
2615 Mistake in MGS command
2616 B-axis mode
2617 Zero setting condition
2618 Workpiece detection sensor not ready
2619 Mistake in SW command
2622 Unset system variable read
2623 B-axis no spec.
2624 Tow-along steady rest type-B no spec
2625 Tow-along steady rest movement condition
2626 W-axis overlap
2628 Mistake in TW command
2629 Mistake in FW command
2630 Mistake in SC command
2631 DNC-DT Path name
2632 DNC-DT Program select
2633 DNC-DT Preload error
2634 DNC-DT Delete error
2635 Y-axis mode
2637 No axis movement command
2638 A/B saddle synchronized motion command
2639 Unable to issue C-axis command during helical cutting
2640 AC thread rotation count error
2641 AC thread fluctuation control not possible
2642 READ/WRITE No empty SAT
2643 READ/WRITE File open
2644 Unusable PRINT request
2645 YS-axis position
2646 SYSTEM VARIABLE C-axis separation
2648 MG tool ready cycle no spec.
2649 SYSTEM VARIABLE Y-axis mode
2650 SYSTEM VARIABLE B-axis mode
2651 C-axis multi rotation mode
2652 Mistake in HA command
2653 Mistake in MN command
2654 Hob circular cutting command
2655 Hob cutting command
2657 SYSTEM VARIABLE C-axis connect
2658 B-axis independent encoder error
2659 NC tailstock position error
2662 NC TAILSTOCK no spec.
2663 Turning cut condition interlock
2667 X-axis mirror image coordinates selected
2668 X-axis mirror image coordinates impossible
2671 C-axis sync control no spec.
2672 C-axis sync command format
2674 Default status macro cannot be executed
2675 Tool posture command error
2676 Tool posture command angle conversion error
2677 Attachment change not possible
2678 SPM contour control not possible
2679 Mistake in Q command
2682 Magnetic encoder speed detection error
2683 MCS Rotary encoder 5 initialization failure
2684 MCS Rotary encoder 5 error
2685 MCS Rotary encoder 4 initialization failure
2686 MCS Rotary encoder 4 error
2687 MCS Rotary encoder 3 initialization failure
2688 MCS Rotary encoder 3 error
2689 MCS Rotary encoder 2 error
2690 MCS Rotary encoder 1 initialization failure
2691 MCS Rotary encoder 1 error
2692 MCS Linear scale 4 initialization failure
2693 MCS Linear scale 4 error
2694 MCS Linear scale 3 initialization failure
2695 MCS Linear scale 3 error
2696 MCS Linear scale 2 initialization failure
2697 MCS Linear scale 2 error
2698 MCS Linear scale 1 initialization failure
2699 MCS Linear scale 1 error
2700 No workpiece confirmation error
2701 Sequencer Error
2702 Spindle command during C-axis connection
2703 Chucking miss
2704 Chucking miss air off order impossible
2705 Tailstock quill over advance
2706 Polygon cutting command condition
2707 Invalid command during polygon cutting
2708 Invalid rotation tool gear
2709 Sub-spindle synchronization interlock
2710 Sub-spindle synchronization cutting
2711 Door open
2712 ATC no spec.
2713 Invalid ATC syntax
2714 Invalid ATC TC no.
2716 Invalid ATC TL no.
2717 Invalid ATC MT no.
2718 Invalid ATC MG no.
2719 Invalid ATC command
2720 M06/M228 interlock
2721 Turret number mismatch
2722 Robot/Loader request illegal
2723 ATC next tool preparation interlock
2724 Invalid ATC sub arm
2725 Invalid RS tool L/M
2726 Magazine encoder read
2727 Magazine rotation interlock
2728 Invalid magazine tool no.
2729 No magazine return pot
2730 Tool insertion interlock
2732 Tailstock sleeve position data error
2733 Coolant flow
2734 Coolant level
2735 Spindle low rotation command
2736 SVP time constant switching no spec.
2737 Invalid tailstock switch position
2738 Synchronous hobbing interlock
2739 Invalid synchronous hobbing mode
2740 Incorrect magazine tool data
2741 Touch setter unlock time over
2742 Setup switch ON
2743 Irregular coolant level
2744 Tool breakage
2745 Low high-pressure coolant pressure
2746 Hydraulic oil unit error
2747 Index disable position
2748 CPU fan stop
2749 Hydraulic oil level lower limit
2750 Tool monitoring unit error detection
2751 Coolant/Oil mist command
2752 Air pressure
2753 Unable to change tool
2754 Invalid coolant command
2755 Semi-dry unit error
2756 Actual tool data setting
2757 Oil mist unit error
2758 Invalid position data
2759 Coolant discharge error
2760 Sub-spindle rotation tool interlock
2761 W-axis overlap mode
2762 Chucking miss
2763 Coolant filter
2764 Coolant error
2765 Chip conveyer filter clogged
2766 Invalid M-tool spindle command
2767 M-spindle low rotation interlock
2768 Program check mode interlock
2769 Invalid spindle control command
2770 SVP time constant switching command
2771 APC clamp confirmation
2772 APC system mode
2773 APC M command
2774 Thread cutting cycle interlock
2775 Sensor head interlock
2776 M command not completed
2777 Cross rail positioning sensor error
2778 Cross rail motor overload
2779 Axis lube motor overload
2780 Axis lube pressure ON confirmation
2781 No AT command
2782 Axis lube pressure OFF confirmation
2783 Oil hole motor overload
2784 Invalid MT command
2785 Invalid AT command
2786 No S command
2787 No SB command
2788 Invalid SB command
2789 Coolant tank filter clogged
2790 Shower coolant motor overload
2791 M spindle head cooling unit
2792 Invalid RH command
2793 Incorrect attachment index position
2794 Mist air lube unit
2795 Warming up error
2796 Sequence restart
2797 Axis interlock release
2798 Invalid BC command
2800 Alarm detected from externally connected device
2801 Turret rotation interlock
2802 Invalid long boring bar command
2803 ATC tool data setting
2804 Attachment control
2805 Limit confirmation impossible
2806 Door interlock
2807 Invalid M code
2848 Chip conveyer overload
2849 Sensor unit in interference range
2850 External request interlock
2851 Machine change M-code
2852 Hand open/close interlock
2853 Teaching operation interlock
2854 Machine linked M-code
2855 Coolant filter
2856 Coolant motor overload
2857 UNUSABLE M-code
2858 Hand slide advance interlock
2887 Coupling device interlock
2888 Lube tank level
2890 Workpiece clamp miss
2891 Tailstock air miss
2892 Unable to execute air shut-off command
2893 Hydraulic oil controller faulty
2894 Spindle lubricant controller error
2895 Coolant controller error
2896 No touch setter
2897 Unloader no spec.
2898 Unloader interference position
2899 Gauge error
2900 DIRECTION V variable
2901 DIRECTION Check address
2902 DIRECTION Data operation
2903 DIRECTION Character use
2904 DIRECTION Numerical data
2905 DIRECTION Parameter/point
2906 DIRECTION Register
2907 DIRECTION F
2908 DIRECTION E
2909 DIRECTION Sequence no.
2910 UNUSABLE G-code
2911 UNUSABLE M-code
2912 UNUSABLE Address character
2913 UNUSABLE Mnemonic
2914 UNUSABLE Left side direction
2915 EXPRESSION Calculation
2916 EXPRESSION Syntax
2917 EXPRESSION Right side
2918 EXPRESSION Left side
2919 EXPRESSION Buffer over
2920 VARIABLE Buffer over
2921 PROGRAM DIRECT Program name
2922 PROGRAM DIRECT V variable
2923 PROGRAM DIRECT Character use
2924 PROGRAM DIRECT G-code
2925 BRANCH Sequence name
2926 BRANCH Condition
2927 Parameter setting illegal
2928 Parameter playback impossible
2929 Register setting impossible
2930 Program plus var. limit over
2931 Program minus var. limit over
2932 Program request illegal
2933 Program request impossible
2934 Program external request impossible
2935 No program selection
2936 No program
2937 Program end code
2938 Program analysis complete
2939 SUB PROGRAM stack
2940 SUB PROGRAM Program name
2941 SUB PROGRAM Buffer over
2942 Command impossible while running
2943 Data file read
2944 Comment end code not found
2945 Equal does not exist
2946 No spec.
2948 DIRECTION Y
2949 DIRECTION Z
2950 DIRECTION D
2951 DIRECTION L
2952 DIRECTION SU
2953 DIRECTION Torque limit
2954 PROGRAM DIRECT M-code
2955 PROGRAM DIRECT Equal
2956 Machine change M-code
2957 G22 feed
2958 Main sequence
2959 Barrier limit
2960 User reserve code
2961 Calculation function no spec.
2962 Subscript function no spec.
2964 NC program selection
2965 EXPRESSION subscript
2966 M code time over
2967 Cycle time over
2968 Program selection
2969 G23 FEED
2970 DIRECTION X
2971 DIRECTION I
2972 DIRECTION J
2973 DIRECTION K
2974 PROGRAM DIRECT hexadecimal data
2975 PROGRAM DIRECT character string
2976 Stopper position data illegal
2977 Program selection unsuitable
2978 DIRECTION V
2979 DIRECTION C
2980 No decimal point
2981 DIRECTION Q
2982 Time over

Lỗi máy CNC Okuma Alarm C List

Sau đây là liệt kê danh sách Lỗi máy CNC Okuma Alarm C List for Okuma OSP-P300S/P300L CNC systems.

3055 Device temperature too high
3056 Non-functioning device detected
3057 Unable to start during virus scan
3120 Overload detected.
3122 Maintenance (by user) necessary
3132 VDU communication error
3133 VDU detected error
3134 VDU initialization failure
3135 MCS DD encoder link error
3136 MCS DD Encoder error
3137 MCS DD Encoder (slave sensor) error
3138 MCS DD encoder initialization failure
3139 MCS DD encoder (slave sensor) initialization failure
3144 MCS Power supply unit overload
3150 MCS Undefined alarm number
3151 MCS Inverter unit fault
3152 Mistake in data from MCS to NC
3153 MCS CON APA deviation
3154 MCS Power supply unit error
3155 MCS Converter link error
3156 MCS DC-bus voltage alarm
3157 MCS Motor overcurrent
3158 MCS Power unit overheat
3159 MCS Power unit overload
3160 MCS Supply voltage flutter
3161 MCS Inverter capacity differs from spec.
3162 MCS Winding change failure
3163 MCS Encoder link error
3164 MCS Encoder detected error.
3165 MCS Encoder initialization failure
3166 MCS Encoder with shaft detected error
3167 MCS Encoder with shaft initialization failure
3168 MCS ABSO SCALE error
3169 MCS ABSO SCALE initialization failure
3170 MCS Magnetic encoder alarm
3171 MCS Resolver alarm
3172 MCS Pulse generator count over
3173 MCS Motor overheat
3174 MCS Servo link error
3175 MCS Servo link disconnection
3176 Mistake in data from NC to MCS
3177 MCS Servo data error
3178 MCS Illegal command
3179 MCS CON speed over
3180 MCS Speed command over
3181 MCS DIFF over
3182 MCS APA speed over
3183 MCS Full-closed APA error
3184 MCS Over speed
3185 MCS Speed deviation over
3186 MCS Collision detected
3187 MCS Urgent-stop time over
3188 MCS Belt is broken
3189 MCS Axis change control error
3190 MCS Independent encoder initialization failure
3191 MCS Calculated current position lies outside range
3192 MCS Motor overload
3194 MCS ABSO SCALE sub-slider detected error
3195 MCS Tandem control communication error
3196 MCS Full abso scale link error
3197 MCS Full abso scale error
3198 MCS Full abso scale initialization failure
3199 MCS Axis stop signal error
3202 User reserve code
3203 Warm up run
3204 Running time over
3205 Work counter over
3206 Cycle time over
3207 DNC Start conditions
3208 DNC Initialization sequence impossible
3209 DNC Illegal text from host
3210 DNC Incorrect machine No.
3211 DNC Text format error
3212 DNC Text receipt error
3213 DNC Text transmission error
3214 FMS Coupling mode change
3215 FMS HOST CPU alarm
3216 FMS Operation mode select
3217 DNC-B buffer operation
3218 DNC-B buffer operation change
3226 Common unit illegal
3231 Program select
3232 Load monitor overload
3238 ROBOT alarm/reset
3240 LOADER alarm/reset
3241 Post-process gauging Unable to transmit
3242 Post-process gauging Unable to receive
3243 Post-process gauging Time out
3244 Post-process gauging Data format error
3245 Gauging data out
3246 CEJ MATIC Data NG
3247 CEJ MATIC Data read
3248 Size catcher Data NG
3249 Size catcher Gauging error
3250 Size catcher Unable to transmit
3251 Size catcher Unable to receive
3252 Size catcher Time out
3253 Size catcher Data format error
3254 Schedule program start
3255 Main program start
3261 Tool life management No spare tool.
3264 RS-232C communication illegal
3266 Workpiece counter full count
3271 Gauging sensor battery change
3279 DNC Machining start conditions
3280 DNC Data receipt start conditions
3289 Load monitor low load
3295 Quality check alarm
3300 Tool data output
3314 External tool offset input
3316 Position encoder adjustment required.
3319 DNC Ethernet receipt command not allowed.
3320 DNC Ethernet receipt error
3321 DNC Ethernet transmission error
3331 NC tailstock position error
3332 Reboot machine.
3682 Magnetic encoder speed detection error
3683 MCS Rotary encoder 5 initialization failure
3684 MCS Rotary encoder 5 error
3685 MCS Rotary encoder 4 initialization failure
3686 MCS Rotary encoder 4 error
3687 MCS Rotary encoder 3 initialization failure
3688 MCS Rotary encoder 3 error
3689 MCS Rotary encoder 2 error
3690 MCS Rotary encoder 1 initialization failure
3691 MCS Rotary encoder 1 error
3692 MCS Linear scale 4 initialization failure
3693 MCS Linear scale 4 error
3694 MCS Linear scale 3 initialization failure
3695 MCS Linear scale 3 error
3696 MCS Linear scale 2 initialization failure
3697 MCS Linear scale 2 error
3698 MCS Linear scale 1 initialization failure
3699 MCS Linear scale 1 error
3700 Power save ON
3701 CPU temperature
3702 Warm up run
3703 Oil filter
3704 Lube tank flow
3705 Lube tank level
3706 Spindle lube pressure
3707 Spindle cooler error
3708 Oil cooler error
3709 Coolant level
3710 Air blow pressure
3711 Air pressure
3712 Program selection interlock
3713 Chip conveyer overload
3714 ZA-axis overload
3715 ZB-axis overload
3716 XA-axis overload
3717 XB-axis overload
3718 Coupling device error
3719 ROBOT control
3720 ROBOT alarm/reset
3721 ROBOT/LOADER control
3722 LOADER alarm/reset
3723 Schedule program start
3724 Main program start
3725 CEJ MATIC data NG
3726 CEJ MATIC data read
3727 Auto power off impossible
3728 Oil cooler level
3729 Coolant error
3730 Coolant flow
3731 Coolant abnormal
3732 Robot/loader axis safety speed over
3733 Robot/loader safety speed monitor error
3734 ATC step time over
3735 Next tool preparation impossible
3736 Coolant filter
3737 Mist collector
3738 Mode switch operation prohibited
3739 Control box air conditioner error
3740 Air filter clogged
3741 Index chuck oil level
3742 ATC-axis circuit breaker
3743 ATC-axis motor overload
3744 Chucking miss air
3745 Mist lubrication unit
3746 External start switch
3747 NC start button
3748 Door sensor
3749 Automatic lubrication system error
3750 Tailstock absolute encoder error
3751 Invalid external tool offset input
3752 Coolant supply
3753 Drain tank
3754 Mist collector
3755 Workpiece conveyor error
3756 Unmachined workpiece detection
3757 Bar feeder error
3758 Oil mist error
3759 Tool monitoring unit error detection
3760 Fan cooling unit pressure
3761 TOOL change not possible
3762 ACC step time over
3763 Switch disabled
3764 Oil controller unit
3765 Spindle vibration sensor
3766 Coupling device interlock
3767 Tailstock holding miss check air
3768 Irregular coolant level
3769 Side cover open
3770 Safety door open
3771 Lube tank motor run time over
3772 Coolant flow
3773 Earthquake detected
3774 EC circuit breaker
3775 Lubrication unit error
3777 Air blow flow
3778 M axis cooling fan overload
3779 APC system conditions
3780 Touch setter unit error
3781 EC overload
3782 Sensor contact signal error
3783 ATC interlock
3784 Fire extinguish unit power OFF
3785 Spindle lubrication unit
3786 Chip flush-out motor overload
3787 M-axis unit command mismatch
3788 AAC system condition
3789 Air dryer unit error
3790 Ext. program select parity check
3791 Mist air lubrication unit
3792 Chucking miss
3793 Coolant level low
3794 Power source unit overload
3795 Hydraulic oil unit
3796 RSS unit battery error
3797 RSS unit communication error
3798 Unloader interlock
3800 Transfer data error
3843 Safety fence open
3844 Invalid loader grease lubrication input
3845 Coolant level lower limit
3846 M/C panel at interfering position
3847 Invalid limit/proximity switch
3848 Anti-gouge unit faulty
3849 Tool counter full count
3850 External alarm
3851 Tool counter faulty
3852 Tail stock chuck position
3853 Invalid loader limit/proximity switch
3854 Chip conveyor stop
3855 Oil air unit oil level low
3856 Coolant motor overload
3857 Oil skimmer overload
3858 Chuck grip confirmation unit faulty
3859 Fire extinguisher error
3860 Fire extinguisher power OFF or error
3861 Chip conveyer filter clogged
3862 Filtration unit error
3874 Sub chip conveyor error
3875 Absolute encoder controller error
3876 Workpiece loading unit stop signal ON
3877 Workpiece counter full count
3878 Concentrated chip conveyor
3879 Gauging NG
3880 Spindle air purge pressure
3881 Turnover cycle time over
3882 Start impossible
3883 Chip crusher error
3884 Workpiece puller operation incomplete
3885 No workpiece
3886 Workpiece present
3887 Temperature control unit error
3888 Chip conveyor faulty
3889 EExternal start signal ON
3890 Low level in oil tank
3891 Multi-counter tool life
3892 Hydraulic oil level lower limit
3893 Hydraulic unit oil controller
3894 Spindle lubrication controller error
3895 Coolant controller error
3896 Tool change count-up
3897 Workpiece stocker full
3898 Cooler error
3900 User reserve code
3901 External

Lỗi máy CNC Okuma Alarm D List

Sau đây là liệt kê danh sách Lỗi máy CNC Okuma Alarm D List for Okuma OSP-P300S/P300L CNC systems.

4035 Replace memory board battery
4036 Key-code data receipt error
4037 CCP-CPU error
4052 PLC backup data file write
4054 ACP key-code data receipt error
4055 Safety speed clamping
4056 Adjusting Type-J encoder
4057 Battery life
4058 Previous backup error
4059 Backup file error
4060 AlarmService internal error
4061 UPS Service error
4062 Remote Diagnosis error
4063 DNC2 communication error
4064 Awaiting establishment of DeviceNet
4065 FL-net transmission error
4066 FL-net transmission failure
4067 Maintenance necessary
4068 Non-responsive software detected
4069 Turret index sequence has not ended.
4070 Solid model position error
4071 CAS environment file cannot be changed
4072 Turret position error
4076 CAS software calculation error
4077 Turning interlock of CAS
4078 Error occurred during CAS
4080 Collision Avoidance Function OFF
4081 In-position/droop check waiting status
4083 Windows updated. Reboot
4084 Virus has been detected.
4085 Fan motor error at panel computer unit
4086 UPS not functioning
4087 Non-functioning device detected
4088 Virus Detect Function active
4090 Machine relocation detected
4091 Var. lost motion cannot be applied.
4092 MCS Parameter learning
4100 Collision avoidance position
4101 CAS software environment being changed
4102 Awaiting CAS software process
4103 Drawing speed over
4104 CAS processing time over
4105 Collision block detected
4106 Collision Avoidance system OFF
4107 Awaiting CAS check result
4108 Inaccurate material shape
4109 CAS operating in rapid mode
4110 Turret collision check not performed
4120 Overload detected
4121 General overload detection disabled
4122 Maintenance (by user) necessary
4130 MCS Inertia identification
4131 VDU initialization failure
4132 VDU communication error
4133 VDU error
4134 MCS Alarm-D occurred
4135 MCS DD encoder link error
4136 MCS DD encoder error
4137 MCS DD encoder (slave sensor) detected error
4138 MCS DD encoder initialization failure
4139 MCS DD encoder (slave sensor) initialization failure
4141 MCS Push reset button to stop spindle
4144 MCS power supply unit overload
4145 MCS Drive unit external cooling fan stop
4147 MCS Drive unit internal cooling fan stop
4148 MCS Power supply unit external cooling fan stop
4149 MCS Power supply unit internal cooling fan stop
4150 MCS Undefined alarm number
4151 MCS Inverter unit fault
4152 Mistake in data from MCS to NC
4153 MCS CON APA deviation
4154 MCS Power supply unit error
4155 MCS Converter link error
4156 MCS DC-bus voltage alarm
4157 MCS Motor overcurrent
4158 MCS Power unit overheat
4159 MCS Power unit overload
4160 MCS Supply voltage flutter
4161 MCS Inverter capacity differs from spec.
4162 MCS Winding change failure
4163 MCS Encoder link error
4164 MCS Encoder detected error
4165 MCS Encoder initialization failure
4166 MCS Encoder with shaft detected error
4167 MCS Encoder with shaft initialization failure
4168 MCS ABSO SCALE error
4169 MCS ABSO SCALE initialization failure
4170 MCS Magnetic encoder alarm
4171 MCS Resolver alarm
4172 MCS Pulse generator count over
4173 MCS Motor overheat
4174 MCS Servo link error
4175 MCS Servo link disconnection
4176 Mistake in data from NC to MCS
4177 MCS Servo data error
4178 MCS Illegal command
4179 MCS CON speed over
4180 MCS Speed command over
4181 MCS DIFF over
4182 MCS APA speed over
4183 MCS Full-closed APA error
4184 MCS Over speed
4185 MCS Speed deviation over
4186 MCS Collision detected
4187 MCS Urgent-stop time over
4188 MCS Belt is broken
4190 MCS Independent encoder initialization failure
4191 MCS Calculated current position lies outside range
4192 MCS Motor overload
4194 MCS ABSO SCALE sub-slider detected error
4195 MCS Tandem control communication error
4196 MCS Full abso scale link error
4197 MCS Full abso scale error
4198 MCS Full abso scale initialization failure
4199 MCS Axis stop signal error
4200 Reboot enabled parameter set
4201 MACHINING MANAGEMENT data backup stop
4202 DNC-B Communication system abort
4203 DNC-B Communication error
4204 DNC-B Message format error
4205 H1 turret interference barrier parameter not set
4206 SPM Parameter unsuitable
4207 Unable to execute Hi-CUT Pro control
4208 G265/G264 commands: Unusable address character
4209 Hi-CUT Pro parameter out of range (replacing)
4210 SPM contour control not possible
4211 SPM parameter out of range (replacing)
4214 RS232C communication not ready
4215 Communication buffer over
4216 Communication procedure No response
4217 Communication procedure NAK/WACK
4218 Communication procedure Illegal text
4219 Communication procedure ENQ
4220 Communication procedure EOT
4221 Communication procedure TTD
4223 Motor not ready to start
4224 Canceling stroke end limit
4225 Pitch compensation data calculation
4226 MSB load error
4227 External start not possible
4228 SSynchronized rotation speed over
4230 Torque limit recovery
4232 Backup data read/write
4237 Magazine operation panel communication error
4238 Please open magazine door
4240 Tool life management No spare tool
4242 Parameter set value incorrect
4245 Waiting program selection during program operation.
4247 Main spindle max. speed designation
4248 DNC NC receipt start conditions
4249 Tool life warning
4251 Axis feed rate restriction
4252 Detector operation check mode
4258 Y-axis cancel mode
4261 Workpiece counter over
4267 PLC link error
4268 PLC communication error
4269 ROBOT control
4274 User reserve code
4281 Workpiece counter over
4284 Thermistor error
4285 Thermal deviation compensation
4288 PSC Learn converge protect error
4289 Spindle able to enter transportation barrier
4290 TCP/IP communication error
4291 Position encoder auto adjustment
4292 Please check the program
4294 Extended Y-axis plus variable limit
4295 TDC parameter not set
4297 Main Magazine tool Quantity over
4298 DNC Ethernet communication error
4300 B-axis independent encoder connecting
4301 Tail-stock position error
4302 Please supply oil of chuck
4303 Movement to sizing position stopped
4304 No axis movement after offset change
4305 Y-axis not at turning position
4306 Turret movement decelerating
4307 Alarm-A at other system
4308 X-axis over limit
4309 Clutch A slip monitor OFF
4311 Interrupt program
4314 Learning required for cam data
4315 Permissible value exceeded
4316 Manual feed invalid
4345 Unable to execute feed axis retract function
4346 ZA-W interference parameter not set
4347 TDC invalid
4348 X-C-axis coordinate value error
4349 Mode switching impossible
4682 Magnetic encoder speed detection error
4683 MCS Rotary encoder 5 initialization failure
4684 MCS Rotary encoder 5 error
4685 MCS Rotary encoder 4 initialization failure
4686 MCS Rotary encoder 4 error
4687 MCS Rotary encoder 3 initialization failure
4688 MCS Rotary encoder 3 error
4689 MCS Rotary encoder 2 error
4690 MCS Rotary encoder 1 initialization failure
4691 MCS Rotary encoder 1 error
4692 MCS Linear scale 4 initialization failure
4693 MCS Linear scale 4 error
4694 MCS Linear scale 3 initialization failure
4695 MCS Linear scale 3 error
4696 MCS Linear scale 2 initialization failure
4697 MCS Linear scale 2 error
4698 MCS Linear scale 1 initialization failure
4699 MCS Linear scale 1 error
4700 External cycle start interlock
4701 Chip conveyer overload
4702 Cycle start interlock
4703 Canceling stroke end limit
4704 Please open door
4705 Door interlock all axis stop
4706 Canceling door interlock
4707 Enabling Switch faulty
4708 ATC system mode
4709 Power sequence error
4710 Parameter non set
4711 Spindle motor not ready to start
4712 Reboot enabled parameter set
4713 Executing power OFF sequence
4714 Workpiece counter full count
4715 Preparing for warming up
4716 Motor not ready to start
4717 Dual cycle start button interlock
4718 Invalid parameter setting
4719 Please open side cover
4720 Dual cycle start button interlock
4721 Feed rate limitation
4722 System check mode
4723 Machine enabling button pressed
4724 Please open safety fence
4725 Please close front door
4726 Opposite side front door open
4727 Safety fence open
4728 Please close other side front door
4729 Please open magazin door
4730 Magazine door open
4731 Multiple safety guards open
4732 Gauging sensor power ON
4733 Measurement system error
4734 Please close safety guards
4735 Full of chips
4736 Sensor head
4737 Other door open
4738 Magazine OP panel COMM error
4739 Turret not ready to start
4740 2nd Spindle control interlock
4741 Magazine operation panel manual interrupt
4742 Turret encoder offset disabled area
4743 Turret index disabled area
4744 Turnover cycle
4745 REDUCE switch operation error
4746 Tool change mode sw operation error
4747 Gauging sensor battery change
4748 Additional coolant level low
4749 Please close door
4750 Safety interlock
4751 Tailstock quill interlock
4752 Tailstock absolute coder error
4753 Workpiece hand control
4754 Bar stock empty
4755 Roof window open interlock
4756 Canceling robot/loader and machine interlock
4757 Sp. oil air lub. air extraction mode
4758 Index chuck adjust mode
4760 Moving to home position
4761 Override condition
4762 Side cover open
4763 Home position return interlock
4764 Spindle orientation interlock
4765 Setup not complete
4766 Setup complete interlock
4767 ACC safety door locking switch NG
4768 Please open ACC safety door
4769 ACC system mode
4770 Mode switch NG
4771 Magnet chuck unclamp cycle
4772 Tool select switch mismatch
4773 ATC shutter barrier area
4774 Invalid zero offset no.
4775 Please open spindle cover
4776 Canceling interference detection
4777 Mist collector power OFF
4778 Side cover open
4779 ATC shutter interlock cancel mode
4780 Maintenance door open
4781 Ladder gate open.
4782 Workpiece stocker error
4783 Workpiece stocker overload
4784 Mist collector error
4785 Self check counter full count
4786 Coolant controller error
4787 Manual tool change enabled
4788 Chip conveyer stop
4789 Sensor overstroke
4790 Chucking miss air route clogged
4791 Linear guide cover interference
4792 Workpiece washer overload
4793 Coolant filter
4794 Sequencer alarm
4795 Please open ceiling door
4796 APC safety interlock
4797 Please open APC door
4798 APC door lock incomplete
4800 Tow-along steady rest connection
4801 Oil mist error
4802 Turret rotation interlock
4803 Cross rail positioning auto set mode
4804 Workpiece washing gun error
4805 Coolant unit error
4806 Lube oil drain tank overflow
4807 Axis lube level low
4808 Coolant level low
4809 ATC step time over
4810 System check
4811 Coolant tank upper level
4812 Chip crusher error
4813 Waiting for workpiece check
4814 Chuck open/close interlock
4815 Attachment turret rotating
4816 Long boring bar interlock
4817 Safety door open interlock
4818 Attachment manual change mode
4819 ATC door not at end of stroke
4820 M-Spindle rotation limit
4821 Steady rest interlock
4822 Feed axis condition
4823 Turret indexing at reduced speed
4824 Setup mode
4825 Axis position encoder control error
4826 General overload detection disabled
4827 Canceling chuck grasp interlockl
4828 Please switch door interlock ON
4829 NC tailstock thrust change interlock
4830 Tool indexing not complete
4831 Door interlock
4844 Coupling device interlock
4845 Coolant level warning
4846 Unloader setting position parameter
4847 Interference area intrusion
4848 No lower table present signal
4849 Coolant level
4850 Safety fence interlock
4851 Door interlock
4852 Canceling stroke end limit
4853 Robot/loader power sequence error
4854 Loader interference
4855 Front door open interlock
4856 Please open safety fence
4857 Please close safety fence
4858 Feed rate limit
4859 Teaching panel enabling switch error
4860 Multiple safety guards open
4861 Equip. safety fence parameter mismatch
4862 Dual cycle start button interlock
4863 Tool change count-up
4864 Other door open
4865 Performing turnover cycle
4866 No workpiece
4867 M-spindle angle uncertain
4868 Cycle start interlock
4869 Chuck was changed
4870 Invalid servo data selection
4871 Inside barrier
4872 Tailstock fretting
4873 Door open/close limit switch NG
4874 XB cover interference
4875 Please push the NC start button
4876 Please discharge coolant
4877 Invalid positioning point
4878 Pulse handle mode
4879 Curvic cover not attached
4880 Measurement unit error
4881 NG chute workpiece present
4882 Quality check counter notice count
4883 Tow-along tailstock unclamp
4884 Tool counter full count
4885 Quality check counter full count
4886 Tool counter warning
4887 Tailstock/Chuck Pedal Enable
4888 Mode switch operation error
4889 PLC link error
4890 Dust collector in local mode
4891 Chip conveyor in local mode
4892 Chip conveyor error
4893 OP panel not at retract position
4894 Multi-counter tool life warning
4895 Hydraulic fluid level low
4896 Lubricant level
4897 Gauging data ready time out
4898 Power save ON
4899 Lower turret origin return interlock
4900 Motor not ready to start
4903 Reboot enabled parameter set
4904 Barrier intrusion
4905 Safety speed clamping
4907 Alarm-A at other system

Lỗi máy CNC Okuma Alarm P List

Lỗi máy CNC Okuma Alarm A List

Lỗi máy CNC Okuma Alarm B List

Lỗi máy CNC Okuma Alarm C List

Lỗi máy CNC Okuma Alarm D List

Để lại một bình luận Hủy

Đăng nhập